Search Plaster Hose and Pumping Equipment 
 

Plaster hose

 

Plaster hose

Plaster hose

plaster pumping hose

Plaster pumping hose

Plaster pumping hose

Plaster pumping hose

Plaster pumping hose

Plaster pumping hose

Plaster pumping hose

plaster pumps

plaster pumps

Plaster Hose

United Equipment Sales sells premium plaster hose, stucco hose and plaster hose nozzles with accessories.

Our plaster pumping hose has one of the highest burst pressure ratings in the industry at 3500 psi.

Plaster hose with high operating pressure, combined with high quality snap couplings and camlock fittings (both heavy duty and threaded ends). Our plaster pumping hose helps you to get more reliability and safety out of your plaster pump.  With the proper fittings on your plaster pumping hose, your workers will be safer and your hose will last longer.  Buy your next plaster hose, nozzles and accessories from UES.

UES also provides several accessories for greater safety and reliability, such as plaster and stucco hose fittings, safety slings, cables or safety chains.

Whipcheck safety cables can ensure pump reliability and prevent injury and property damage by ensuring against dangerous decoupling accidents.

At United Equipment Sales, we provide everything you need to get optimal efficiency out of your plaster pump investment. We also sell a full line of heavy duty construction hose, such as gunite hose, gunite parts, plaster material hose, nonmarking hose, fiberbound hose, material handling hose, mortar mixer hose, plaster material hose, wiremesh hose and shotcrete hose as well as everything you need in plaster hose accessories such as plaster hose clamps, plaster hose fittings, plaster hose heavy duty ends, shotcrete hose fittings, and other mortar mixer hose accessories.

United Equipment Sales can also provide you with a full range of plaster hose nozzles, including: plaster pole gun nozzles, fireproofing nozzles, browning nozzles and EIFS nozzles. We also provide a complete line of masonry wall hooks, block fit nozzles, finish nozzles and stucco nozzles as well as slabjack nozzles, packer nozzles and door frame nozzles. United Equipment Sales specializes in used concrete pumps of all types from Putzmeister, Schwing, Mayco, Reed, Olin, Transcrete and others. CALL US for the BEST PRICES on all heavy duty construction equipment.


Non-Destructive Hose Pressure Tests
Questions Contact (503) 283-2105

For plaster, shotcrete, gunite and concrete stucco applications; review below non-destructive tests on a full length of plaster hoses or hose assembly for the purpose of eliminating any potential defects which cannot be seen by visual examination or in order to determine certain characteristics of the hose while it is under internal pressure. Click Here Concrete Pumping, Stucco, Plaster Fireproofing Accessories for Sale

a. A proof pressure test is normally applied to hose for a specified period of time. On new hose, the proof pressure is usually 50% of the minimum specified burst except for woven jacket fire hose where the proof pressure is twice the service test pressure marked on the hose (67% of specified minimum burst). Hydrostatic tests performed on fire hose in service should be no higher than the service test pressure referred to above. The regulation of these pressures is extremely important so that no deteriorating stresses will be applied, thus weakening a normal hose.

b. A hold test, when required, is a means of determining whether weakness will develop under a given pressure for a specified period of time.Percent length change elongation or contraction) is the difference between the length at 10 psi {0.069 MPa)(except wire braided or wire spiraled) and that at the proof pressure times 100 divided by the length at 10 psi (0.069 MPa). Elongation occurs if the length of the hose under the proof pressure is greater than at a pressure of 10 psi (0.069 MPa). Contraction occurs if the length at the proof pressure is less than at 10 psi (0.069 MPa).

In testing wire braided or spiraled hose, the proof pressure is applied and the length recorded. The pressure is then released and, at the end of 30 seconds, the length is measured; the measure- ment obtained is termed the "original length." Click Here Best Prices Top Quality Fabric and Wire Hoses over 3100 psi burst pressure Ratings

c. Percent change in outside diameter or circum ference is the difference between the outside diameter or circumference at 10 psi (0.069 MPa) and that obtained under the proof pressure times 100 divided by the outside diameter or circum ference at 10 psi (0.069 MPa). Expansion occurs if the measurement at the proof pressure is greater than at 10 psi (0.069 MPa). Contraction occurs if the measurement at the proof pressure is less than at 10 psi (0.069 MPa).

d. Warp is the deviation from the straight line drawn from fitting to fitting; the maximum deviation from this line is warp. First, a measurement is taken at 10 psi (0.069 MPa) and then again at the proof pressure. The difference between the two, in inches, is the warp. Normally this is a feature measured on woven jacket fire hose only.

e. Rise is a measure of the height a hose rises from the surface of the test table while under pressure. The difference between the rise at 10 psi (0.069 MPa) and at the proof pressure is reported to the nearest 0.25 inch (6.4 mm). Normally, this is a feature measured on woven jacket fire hose only.

f. Twist is a rotation of the free end of the hose while under pressure. A first reading is taken at 10 psi (0.069 MPa) and a second reading at proof pressure. The difference, in degrees, between the 10 psi (0.069 MPa) base and that at the proof pressure is the twist. Twist is reported as right twist (to tighten couplings) or left twist. Standing at the pressure inlet and looking toward the free end of a hose, a clockwise turning is right twist and counterclockwise is left twist.

g. Kink test is a measure of the ability of woven jacket hose to withstand a momentary pressure while the hose is bent back sharply on itself at a point approximately 18 inches (457mm) from one end. Test is made at pressures ranging from 62% of the proof pressure on sizes 3 inches (76 mm) and 3.5 inches (89 mm) to 87% on sizes under 3 inches (76 mm). This is a test applied to woven jacket fire hose only.

h.Volumetric expansion testis applicable only to specific types of hose, such as hydraulic or power steering hose, and is a measure of its volumetric expansion under rangesof internal pressure.